Zebra printer z4000 manual

For over 25 years, Zebra Technologies Corporation has provided customers with the highest caliber of products and support. This guide is available by contacting your distributor or Zebra Technologies Corporation. In addition, label preparation software is available. Contact your distributor or Zebra Technologies Corporation for further information.

Zebra Technologies Corporation is not responsible for any damage incurred during shipment of the printer and will not cover the repair of this damage under its warranty policy. Any damage claim should be filed with the shipping company. Refer to Figure 1. NOTE: You must supply the interface cable for your application. The AC Power Cord must have a three-prong female connector on one end which plugs into the mating connector c at the rear of the printer.

If a power cable was not included with your printer, refer to Appendix C at the back of this guide. For personnel and equipment safety, always use a three-prong plug with an earth ground connection to the AC Power Source. With the deluxe front panel, the LCD displays the parameters during the configuration process.

This permits two sources to send label formats to the printer. The serial interface is factory preset to match the typical PC environment with RS communication:. If you do not know the settings of your host computer, refer to the instruction manual provided with the computer or your software application.

The printer automatically senses if a parallel communications cable is connected from your host computer. When shipped from the factory, the printer is preset to the most commonly used modes of operation:.

Press the Printhead Open Lever e. Fold down the Media Supply Guide g and slide it out as far from the printer frame as possible. Slide the Media Guide h out as far from the printer frame as possible.

Determine the type of media required for your application and follow the roll media or fanfold media loading procedure. Place the roll of media on the Media Supply Hanger i and push it on all the way. Fold the Media Supply Guide g up and slide it against the outer edge of the media roll. Feed the media under the Media Spindle j , under the Ribbon Sensor k , and out the front of the printer. Slide the Media Guide h in until it is against the outer edge of the media.

Pass the fanfold media over the Media Supply Hanger i. Fold the Media Supply Guide g up and slide it against the outer edge of the media. Slide the Media Guide h against the outer edge of the media. Most applications require the spindle to be in the "Normal" position. The "Low-Tension" position is recommended only when wide ribbons are used and normal tension hampers the ribbon movement.

To place this spindle in the "Normal" position, firmly pull out on the Spindle End-Cap until it clicks into place as shown in Figure 5a. To place the spindle in the "Low-Tension" position, firmly push in on the Spindle End-Cap until it clicks into place. The smooth backing of the ribbon protects the printhead from wear. For Direct Thermal printing, do not load ribbon in the printer. Place the roll on the Ribbon Supply Spindle l and push it on all the way.

Pull the end of the ribbon over the Ribbon Sensor k , under the Printhead assembly f , and up over the Ribbon Guide Plate m. Wind the ribbon onto the Take-up Spindle n for several turns in a clockwise direction. Product Warranty Information. Printer Software License Reset. Manage Software Licensing excluding Printers. Device Diagnostic Tool for Mobile Devices. Find a Zebra Partner. Contact Support. Mobile Computers. Barcode Scanners. Interactive Kiosks. Location Solutions. Intelligent Edge Solutions.

Temperature Monitoring and Sensing. The Zebra S4M. One of our most popular industrial and commercial bar code and shipping label printer. The Zebra ZT is one of our most popular industrial and commercial bar code and shipping label printer. The Zebra Xi4 is one of our most popular industrial and commercial bar code and shipping label printer.

The Zebra ZP printer is very fast and great for all shipping label applications. The Zebra LP thermal label printer is one of the most popular and reliable direct thermal label printers.

The Zebra is perfect for all business thermal label printing applications. The Zebra LP is our slimmest, ultra-thin design thermal label printer. It's best used where space is precious and you need the smallest desktop footprint available. The Zebra LP is our most affordable direct thermal label printer.

The Zebra TLP is a 2-in-1 printer with both thermal and ribbon print heads. This feature makes this label printer very versatile and the ability to print in color with the ribbon printing. The Zebra XiII is one of our most popular industrial and commercial bar code and shipping label printer.

The Zebra S thermal and barcode printer is a great choice label printer for industrial and commercial market applications. You need more credits to purchase this manual. When purchasing the manual, please note that the Payment will be made to TrinixSoft.

This is because TrinixSoft. Once the payment is completed, you will receive an email with link to the manual with in a couple of minutes from the time of purchase.